Brands
Xuron
Hand tools
Interflux
Soldering
Abeba
Premium Footwear
Kyzen
Cleaning Chemistries
RubisTech
Tweezers
Permabond
Adhesives
ASM
DEK Consumables
Polyco
Hand protection
CHT
Silicones

Product Selection support

Request supportContact us
Services
Dross/Waste metal collection
Waste metal collection
Technical Support
Email: Technical@temple4.com
Phone: 01730 888499
About
News
October 31, 2021

Temple4 are appointed exclusive Kyzen distributor for Ireland

February 5, 2021

Temple4 becomes ASM DEK Consumables UK distributor/partner

September 12, 2020

Temple4 Becomes CHT/ACC Silicones – Preferred UK Partner & Supplier

May 17, 2020

A look Kyzen's new Aquanox line Aquanox A4727

View all posts
Contact

Full Plastic Tweezers

Tweezers KR

Tweezers KR

Rework & Repair


Rework and repair on an electronic unit can be performed on defective electronic units that return from the field but can also be necessary in an electronic production environment to correct defects in the assembly and soldering processes. Typical rework and repair actions involve the removal of solder bridging, adding of solder to poor through hole filled components or adding missing solder, replacing wrong components, replacing components that are placed in the wrong direction, replacing components that have defects related to the high soldering temperatures in the processes, adding components that were left out of the process due to e.g. availability or temperature sensitivity. The identification of these defects can be done by visual inspection, by AOI (Automated Optical Inspection), by ICT (In Circuit Testing, electrical testing) or by CAT (Computer Aided Testing, functional testing). A lot of repair operations can be done with a hand soldering station that has a (de)soldering iron with temperature setting. Solder is added by means of a solder wire that is available in several alloys and diameters and contains a flux inside. In some cases a liquid repair flux and/or a gel flux are used to make the hand soldering process easier. For bigger componnets, like BGAs (Ball Grid Array), LGA's (Land Grid Array) QFNs (Quad Flat No Leads), QFPs (Quad Flat Package), PLCCs( Plastic Leaded Chip Carrier),...a repair unit can be used that simulates a reflow profile. These repair units are available in different sizes and with different options. In most cases they contan a preheating from the bottom side that is usually IR (Infrared). This preheating can be controlled by a thermocouple that is placed on the PCB. Some units have a pick and place unit that facilitates the correct positioning of the component on the PCB. The heating unit is usually hot air or IR or a combination of these two. With the aid of thermocouples on the PCB, the heater is controlled to create the desired soldering profile. In some cases the challenge is to bring the component to soldering temperatures without remelting adjacent components. This can be difficult when the component to be repaired is big and has small components near to it. For BGAs with balls made of a soldering alloy, a gel flux can be used or a liquid flux with higher solid content. In this case the solder for the solder joint is provided by the balls. But also the use of a solder paste is possible. The solder paste can be printed on the leads of the component or on the PCB. This requires a different stencil for each different component. The BGA can also be dipped in a special dipping solder paste that first is printed in a layer with a stencil with one large aperture and a certain thickness. For QFNs, LGAs QFNs, QFPs, PLCCs,...solder needs to be added to make a solder joint. In some cases QFPs can be hand soldered but the technique requires experience so the use of a rework unit is preferred. QFPs and PLCCs have leads and can be used with a dipping solder paste. QFNs, LGA's QFNs who do not have leads but flat contacts cannot be used with a dipping solder paste dipped because their bodies would contact the solder paste. In this case the solder paste needs to be printed on the contacts or on teh PCB. In general it is easier to print solder paste on the component than on the PCB, especially when a so-called 3D stencil is used that has a cavity where the position of the component is fixed. Replacing through hole components can be done with a hand (de)soldering station. This is usually done by placing a hollow desoldering tip over the bottomside of the component lead that can suck away solder from the hole. The desoldering tip will have to heat all the solder in the through hole until it is fully liquid. For thermally heavy boards this can be very difficult. In this case, also the top side of the solder joint can be heated with a soldering iron.  Alternatively the board can be preheated over a preheating before the desoldering operation. Soldering the through hole component is usually done with a solder wire that contains more flux or alternatively extra rework flux is added to the through hole and/or on the component lead. For larger through hole connectors, a dip soldering bath can be used to remove the connector. If accessibilty on the PCB is limited a nozzle with its size adapted to the connector can be used. The use of flux in this operation is recommended.

  • Tips type: fine
  • Curved / angled / bent tip: No
  • Reverse actiont: No
  • Serrated handle: No
  • Serrated inner side: No
  • ESD safe: No
  • Coating:
  • Material: PBT
  • OAL product (mm - in): 120 - 4,72
  • Product width (mm - in): 9 - 0,35
  • Product height (mm - in): 9 - 0,35
  • Tips thickness A (mm - in): 0,4 - 0,015
  • Tips width B (mm - in): 3,2 - 0,12
  • Net weight (g-lb): 6 - 0,13
  • RoHS compliant: Yes

How we can benefit your business

Learn More
HomeAboutContact
Units 14-15, Buriton Business Park, Petersfield, Hampshire
GU32 3NJ

Temple4 Ltd © 2022 All Rights reserved
Privacy policy
Terms of service
Cookies