Typical Uses

Stencil Printing

Stencil printing is the most used method to apply solder paste on the pads of a PCB (Printed Circuit Board) in the SMT (Surface Mount Technology) assembly line in electronics manufacturing. After stencil printing, SMD (Surface Mount Device) components are placed with their solderable contacts on the solder paste and the PCB is transported through a reflow oven where the components are soldered to the PCB board. Stencil printing can also be used to apply solder paste in trough holes for the Pin in Paste (PiP, intrusive reflow) technology that is meant to solder through hole components in the reflow soldering process . Stencil printing can also be used to apply SMT adhesive (glue) to the PCB board. SMD components  are placed with their body on the glue that will be cured in a reflow oven. After that, the SMD components that are glued to the PCB board will be soldered in a wave soldering process.  The PCB board is pressed onto a stencil that has apertures where the solder paste needs to be deposited. A volume of solder paste is present on the stencil. A squeegee is lowered onto the stencil with a certain pressure. The squeegee moves over the stencil with a certain printing speed. This will make the solder paste roll into the apertures. The printing speed can be determined by the desired throughput, typical for high volume productions but can be limited by the used solder paste. This speed can vary from 20-150 mm/s. Once the desired speed has been established, a printing pressure will have to be determined for that printing speed. Higher speeds require higher pressures.  The correct printing pressure is the minimum pressure needed to get a clean stencil after printing, meaning all excessive solder paste  has been removed by the squeegee.  The board is moved away vertically from the stencil, the solder paste releases from the stencil and pads of the PCB have solder paste deposits. The goal is to have a well defined printing result where all solder paste has realeased from the stencil and no solderpaste has been pressed between the stencil and the PCB board. The release of the solder paste obviously is more difficult for smaller apertures and thicker stencils. Some design rules say that the ratio of the surface of the aperture to the surface of the sides ('walls') of the aperture  is preferrably not smaller than 0,6.  The quality of the stencil is a major parameter in good paste release. Rough sides are more likely to adhere solder paste. Different types of stencils exist. The most popular is the stainless steel stencil with laser cut apertures that are smoothened afterwards by a chemical process. Sometimes they are treated with a coating for better paste release. The main reasons for solder paste being pressed in between the stencil and the PCB board is bad sealing between board and stencil or too high printing pressure for the used printing speed. This can lead to solder balling or bridging after reflow.  Some printing machines have an automated under stencil cleaning unit that can be programmed to clean the stencil after so many prints. This will facilitate a stable printing result. It is advisable not to use IPA based or water based cleaning liquids in these units as they may affect the solder paste stability. The use of products that have been specifically designed for that purpose is advisable. The stability of the solder paste on the stencil, meaning how well that the solder paste keeps its printing properties over time, is also a parameter for a stable printing process. Some printing machine have integrated AOI (Automated Optical Inspection) that will check the printing result and give an alarm if it deviates from the programmed desired values. This will help to avoid electronic units being produced with solder joints that are not according good standard.

Dispensing

Dispensing is a technology used in electronics manufacturing to apply solder paste (or an adhesive) from a syringe to a PCB (Printed Circuit Board). Dispensing is a more flexible way to apply solder paste than standard stencil printing because it allows to selectively apply solder paste with the presence of pre-assembled components on the surface. However dispensing is a much slower process than stencil printing and not suitable for high volume productions. That's why it is mostly used to add extra solder paste in an SMT (Surface Mount Technology) assembly line but also for rework and repair and in prototyping. Dispensing can be done manually or automatically.  In rework and repair this is usually done manually with a system that applies pressurised air to the plunger of the syringe and the solder paste is pushed out through a needle. But it can also be done by hand with a manual plunger.  In automated processes like in a stand alone dispenser in a SMT assembly line or a in a dispenser built in a stencil printer there are two main systems to push the solder paste out of the syringe: Air pressure and the Archimes screw. Air pressure systems are usually cheaper but the volumetric stability of the solder paste deposits is a bit more difficult to control, especially when the syringe is almost empty and there is a bigger volume of compressed air in combination of less material in the syringe that needs to be moved by this air pressure. Systems with the Archimedes screw are usually more stable and faster. However depending on the solder paste quality, they can be sensitive to some very fine particles of the solder paste that are squashed between the Archimedes screw and the side walls which can block the needle where the solder paste comes out. The smaller and longer the needle, the higher the risk on needle blocking. The needle size is chosen according to the size of the desired solder deposit. The grain size of the solder paste is chosen according to this needle size. In general a type 3 solder paste can be used for needles with an inner diameter bigger than 0,5mm, a type 4 for needles with an inner diameter down to 0,25mm, a type5 for needles with an inner diameter down to 0,15mm.  The dispensing performance of a solder paste can vary from one type to another in terms of volumetric stability and sensitivity to needle blocking. If a syringe of solder paste has been stored too long, too warm or too cold, this can also affect the dispensing performance. How much time and temperature  will affect the dispensing performance may also vary from one solder paste to another. Solder paste for dispensing can be available in different types of syringes required by the machine where its intended use is for. They can also be available with different types of plungers required by the viscosity of the solder paste to be dispensed. Standard sizes for syringes are 5CC, 10CC and 30CC.


Solder Paste Jetting

Solder paste jetting is a contactless technology used in electronics assembly to apply solder paste to the PCB board. The technology is more flexible than stencil printing because it allows the presence of components on the side of the PCB where the solder paste is being applied. However it is a slower process than stencil printing.  A nozzle jets with high speed small deposits of solder paste to the solderable pads of the SMD (Surface Mount Device) components. The challenge of solder paste jetting is repeatability and stability of the process. A big parameter in this matter is the solder paste. The form stability of the solder paste and the volumetric stability of the deposits in time are important. In many cases the machine manufacturer will test the jetting ability of the solder paste and approve the solder paste for its machine.


Reflow Soldering

Reflow soldering is the most used soldering process in electronics assembly. Mainly SMD (Surface Mount Device) components but also some through hole components are soldered in a reflow oven to a PCB (Printed Circuit Board) by means of a solder paste. The reflow oven is usually a forced convection oven but also vapor phase and IR ovens are possible. The first step of the process is to apply solder paste to the pads of the PCB or in case of through hole components in the through hole. This latter is called Pin in Paste (PiP) or intrusive reflow technology. The main application method is stencil printing but also dispensing and solder paste jetting are possible. Depending on the application method the solder paste will have a different consistency and comes in a different packaging. Solder paste is a mixture of a solder powder and a gel flux. The type of gel flux and the type of powder and in what ratios they are mixed, will determine the consistency of the paste. The solder powder is made of a certain soldering alloy and has a certain grain size (distribution). Finer grains size are used for smaller pitch components and smaller stencil apertures. Dispensing and even more jetting also require finer grain sizes. The gel flux contains substances to deoxydize the surfaces to be soldered. It also contains substances that will determine the consistency and the behavior of the solder paste in the process to a great extent. When stencil printing solder paste, an important parameter is that the solder paste keeps its printing properties during the time it will be on the stencil. This is often referred to as the stability of the solder paste. Solder paste stability is hard to quantify but can be estimated from the stencil life indication in the technical datasheet. After solder paste application SMD components  are placed on the solder paste with their solderable connections. In most cases, this is done with a Pick and Place machine. The solder paste needs to have enough adhesion force to keep the components in their place until soldering. A conveyor will transport the PCB through a reflow oven where the PCB board is submitted to a reflow soldering profile. This profile is created by the temperature settings of the different convection zones. They are usually situated as well from the top as from the bottom side.  Beside the temperature settings, in some cases also the convection rate of the zones can be programmed to get better or lower heat transfer, or when some high components experience too much force from the convection. It is the goal to get all components to soldering temperatures, which is determined by the used soldering alloy, without damaging or overheating temperature sensitive components. This can be a challenge for units with a large diversity of big and small components or an uneven Cu-distribution in the PCB board. In that perspective a low melting point soldering alloy substantially limits the risk of damaging or predamaging components and PCB boards. The speed of the conveyor will determine the time of the profile and the throughput of the oven. In most cases however the Pick and Place process is limiting the throughput.  Not all electronic components are suitable for reflow soldering. Some because of their thermal mass like e.g. big transfos or others because of their thermal sensitivity like e.g. some displays, connectors, relays, fuses,... These components are usually available as a through hole components and soldered in other processes like selective soldering, wave soldering, hand soldering, robot soldering, laser soldering,...

Rework & Repair


Rework and repair on an electronic unit can be performed on defective electronic units that return from the field but can also be necessary in an electronic production environment to correct defects in the assembly and soldering processes. Typical rework and repair actions involve the removal of solder bridging, adding of solder to poor through hole filled components or adding missing solder, replacing wrong components, replacing components that are placed in the wrong direction, replacing components that have defects related to the high soldering temperatures in the processes, adding components that were left out of the process due to e.g. availability or temperature sensitivity. The identification of these defects can be done by visual inspection, by AOI (Automated Optical Inspection), by ICT (In Circuit Testing, electrical testing) or by CAT (Computer Aided Testing, functional testing). A lot of repair operations can be done with a hand soldering station that has a (de)soldering iron with temperature setting. Solder is added by means of a solder wire that is available in several alloys and diameters and contains a flux inside. In some cases a liquid repair flux and/or a gel flux are used to make the hand soldering process easier. For bigger componnets, like BGAs (Ball Grid Array), LGA's (Land Grid Array) QFNs (Quad Flat No Leads), QFPs (Quad Flat Package), PLCCs( Plastic Leaded Chip Carrier),...a repair unit can be used that simulates a reflow profile. These repair units are available in different sizes and with different options. In most cases they contan a preheating from the bottom side that is usually IR (Infrared). This preheating can be controlled by a thermocouple that is placed on the PCB. Some units have a pick and place unit that facilitates the correct positioning of the component on the PCB. The heating unit is usually hot air or IR or a combination of these two. With the aid of thermocouples on the PCB, the heater is controlled to create the desired soldering profile. In some cases the challenge is to bring the component to soldering temperatures without remelting adjacent components. This can be difficult when the component to be repaired is big and has small components near to it. For BGAs with balls made of a soldering alloy, a gel flux can be used or a liquid flux with higher solid content. In this case the solder for the solder joint is provided by the balls. But also the use of a solder paste is possible. The solder paste can be printed on the leads of the component or on the PCB. This requires a different stencil for each different component. The BGA can also be dipped in a special dipping solder paste that first is printed in a layer with a stencil with one large aperture and a certain thickness. For QFNs, LGAs QFNs, QFPs, PLCCs,...solder needs to be added to make a solder joint. In some cases QFPs can be hand soldered but the technique requires experience so the use of a rework unit is preferred. QFPs and PLCCs have leads and can be used with a dipping solder paste. QFNs, LGA's QFNs who do not have leads but flat contacts cannot be used with a dipping solder paste dipped because their bodies would contact the solder paste. In this case the solder paste needs to be printed on the contacts or on teh PCB. In general it is easier to print solder paste on the component than on the PCB, especially when a so-called 3D stencil is used that has a cavity where the position of the component is fixed. Replacing through hole components can be done with a hand (de)soldering station. This is usually done by placing a hollow desoldering tip over the bottomside of the component lead that can suck away solder from the hole. The desoldering tip will have to heat all the solder in the through hole until it is fully liquid. For thermally heavy boards this can be very difficult. In this case, also the top side of the solder joint can be heated with a soldering iron.  Alternatively the board can be preheated over a preheating before the desoldering operation. Soldering the through hole component is usually done with a solder wire that contains more flux or alternatively extra rework flux is added to the through hole and/or on the component lead. For larger through hole connectors, a dip soldering bath can be used to remove the connector. If accessibilty on the PCB is limited a nozzle with its size adapted to the connector can be used. The use of flux in this operation is recommended.

Vapor Phase Soldering

Vapor phase soldering is a type of reflow soldering used in electronics manufacturing that uses heat transferred by a vapor to solder electronic components to a PCB (Printed Circuit Board). The board and components will not be heated higher than the temperature of the vapor which limits the risk on damaging temperature sensitive components and PCB materials. Batch vapor phase ovens as well as in line vapor phase ovens exist but the process is slower than standard convection reflow soldering. The first step of the process is to apply solder paste to the pads of the PCB or in case of through hole components in the through holes. This latter is called Pin in Paste (PiP) or intrusive reflow technology. The main application method is stencil printing but also dispensing and solder paste jetting are possible. After that electronic components are placed with their leads on the solder paste or in the through hole filled with solder paste.   Then the unit will enter the vapor phase chamber which is a confined and closed area where a special liquid is heated up. Due to it's specifically designed composition it will start going into vapor phase at a certain temperature. For lead-free soldering alloys, usually a liquid with a vapor temperature of 230°C is used. The vapor that comes in contact with the colder electronic unit will transfer its heat and condens back into a liquid on the electronic unit. Interaction of this condensed liquid with the solder paste can cause the flux of some solder pastes to flow out over a large area, creating a visually dirty PCB board. Solder pastes for vapor phase soldering like IF 9057 limit this phenomenon to a minimum.  In some machines the PCB can be moved vertically closer to the liquid to improve heat transfer. Together with the electronic unit, the solder paste will be heated over its melting point for a certain amount of time so the solder joints can be formed.  After that some machines will create a vacuum so that the excessive liquid on the electronic unit to evaporates faster and is not dragged out of the machine. The liquid is very expensive. Another reason is to reduce voiding on some components. Voding are gas bubbles of e.g. solder paste flux and others that do not find their way out of the solder joint before solidifying and remain as a cavity that could affect thermal and electrical conductivity and the mechanical strength of the solder joint. In general, the vapor phase atmosphere is more prone for void formation than a normal reflow oven. The vacuum can reduce voiding to a minimum.


Please do contact us on 01730 888499 or info@temple4.com if you require any assistance or need help with the collection of your dross and solder waste, we are here to help.

Technical Data

Rework & Repair


Rework and repair on an electronic unit can be performed on defective electronic units that return from the field but can also be necessary in an electronic production environment to correct defects in the assembly and soldering processes. Typical rework and repair actions involve the removal of solder bridging, adding of solder to poor through hole filled components or adding missing solder, replacing wrong components, replacing components that are placed in the wrong direction, replacing components that have defects related to the high soldering temperatures in the processes, adding components that were left out of the process due to e.g. availability or temperature sensitivity. The identification of these defects can be done by visual inspection, by AOI (Automated Optical Inspection), by ICT (In Circuit Testing, electrical testing) or by CAT (Computer Aided Testing, functional testing). A lot of repair operations can be done with a hand soldering station that has a (de)soldering iron with temperature setting. Solder is added by means of a solder wire that is available in several alloys and diameters and contains a flux inside. In some cases a liquid repair flux and/or a gel flux are used to make the hand soldering process easier. For bigger componnets, like BGAs (Ball Grid Array), LGA's (Land Grid Array) QFNs (Quad Flat No Leads), QFPs (Quad Flat Package), PLCCs( Plastic Leaded Chip Carrier),...a repair unit can be used that simulates a reflow profile. These repair units are available in different sizes and with different options. In most cases they contan a preheating from the bottom side that is usually IR (Infrared). This preheating can be controlled by a thermocouple that is placed on the PCB. Some units have a pick and place unit that facilitates the correct positioning of the component on the PCB. The heating unit is usually hot air or IR or a combination of these two. With the aid of thermocouples on the PCB, the heater is controlled to create the desired soldering profile. In some cases the challenge is to bring the component to soldering temperatures without remelting adjacent components. This can be difficult when the component to be repaired is big and has small components near to it. For BGAs with balls made of a soldering alloy, a gel flux can be used or a liquid flux with higher solid content. In this case the solder for the solder joint is provided by the balls. But also the use of a solder paste is possible. The solder paste can be printed on the leads of the component or on the PCB. This requires a different stencil for each different component. The BGA can also be dipped in a special dipping solder paste that first is printed in a layer with a stencil with one large aperture and a certain thickness. For QFNs, LGAs QFNs, QFPs, PLCCs,...solder needs to be added to make a solder joint. In some cases QFPs can be hand soldered but the technique requires experience so the use of a rework unit is preferred. QFPs and PLCCs have leads and can be used with a dipping solder paste. QFNs, LGA's QFNs who do not have leads but flat contacts cannot be used with a dipping solder paste dipped because their bodies would contact the solder paste. In this case the solder paste needs to be printed on the contacts or on teh PCB. In general it is easier to print solder paste on the component than on the PCB, especially when a so-called 3D stencil is used that has a cavity where the position of the component is fixed. Replacing through hole components can be done with a hand (de)soldering station. This is usually done by placing a hollow desoldering tip over the bottomside of the component lead that can suck away solder from the hole. The desoldering tip will have to heat all the solder in the through hole until it is fully liquid. For thermally heavy boards this can be very difficult. In this case, also the top side of the solder joint can be heated with a soldering iron.  Alternatively the board can be preheated over a preheating before the desoldering operation. Soldering the through hole component is usually done with a solder wire that contains more flux or alternatively extra rework flux is added to the through hole and/or on the component lead. For larger through hole connectors, a dip soldering bath can be used to remove the connector. If accessibilty on the PCB is limited a nozzle with its size adapted to the connector can be used. The use of flux in this operation is recommended.

  • Compliance:  RO L0 to EN and IPC standards
  • Halide content: 0,00%
TDS Download